Pair of EBC FA266 rear brake pads for late type Brembo caliper

Single pin fitting. 2013 onwards V7 models have different two pin pads.

 3 in stock

31654681-z 31654681 GU31654681 31 65 46 81
 3165 4681 3165.4681 31.65.46.81

Kit consisting of black plastic cap and rubber cap seal for PS 12 round handlebar master cylinders and single horizontal outlet remote reservoirs (e.g. BRG19901 )

Also known as Guzzi ref. 17661052, 10271110. Brembo ref. 110430830. This is the smaller of the two round master cylinder caps used on V35, V50, V65 and 850/1000 models

 3 in stock

 10430830 GU10430830 10 43 08 30
 1043 0830 1043.0830 10.43.08.30

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei

Brembo kit containing replacement seal and angled elbow for connecting remote brake fluid reservoir to PS 15, PS 11 and PS 13 rear master cylinders

Also known as Brembo ref. 110312720

 3 in stock

 19659500 GU19659500 19 65 95 00
 1965 9500 1965.9500 19.65.95.00

Rebuild kit for Brembo PS 13 handlebar mounted brake and clutch master cylinders, includes all seals, return spring and brake grease. Piston is hollow

This seal kit is for Cali 1100 master cylinders with a hollow pivot pin, does not fit early models with a solid pivot pin. For Cali EV models this only fits master cylinders with a pair of screws in the middle of the cap, it does not fit the later master cylinder which has diagonally opposed screws. Also know as Guzzi ref. 28659378, 000043851, 30659330. NB Included instructions may refer to rear master cylinder applications rather than front. Brembo ref. 110436250

 3 in stock

Also fits Cagiva Elefant E750, Ducati 748

Brembo brake master cylinder overhaul kit for overhauling foot operated PS 15 master cylinders on linked systems. Includes all seals and brake grease

This seal kit replaces Guzzi part numbers 17659350, 66139790. Brembo ref. 110273920. This repair kit also used on some Cagiva 650 Elefant models and Benelli Sei. Some Nevada 750 models use BRA14701, check your rear master cylinder before ordering. See this link for help with fitting this kit. Supercedes front kit BRA11043
Note that this kit is only for PS15 models where the piston is retained by a ring, if your master cylinder has a circlip retaining the piston then you have a PS 16 and you will need to replace the whole master cylinder - see BRA19001 for a replacement

 3 in stock

 10273920 GU10273920 10 27 39 20
 1027 3920 1027.3920 10.27.39.20

Also fits Benelli Sei, Cagiva Elefant, Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR, Ducati 750 Sport (1972-1974), Laverda Jota

Inner Tacho (rev counter) Cable (fits inside your old cable outer)

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 3 in stock

Complete Speedo (odometer) cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 3 in stock

27760410-z 27760410 GU27760410 27 76 04 10
 2776 0410 2776.0410 27.76.04.10

Complete tacho (rev counter) cable

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 3 in stock

23768110-z 23768110 GU23768110 23 76 81 10
 2376 8110 2376.8110 23.76.81.10

Oil pressure sender

Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.

See ENA12640 for replacement crush washer if required

 3 in stock

19768720-z 19768720 GU19768720 19 76 87 20
 1976 8720 1976.8720 19.76.87.20

1 pin superseal male block connector, used for main loom connections on modern models. See ELA70183 and ELA70184 for the connectors that go in these blocks. Use female connectors with this block

These are a high quality weathertight connector designed to keep corrosive elements out

 3 in stock